Raid 1 Boot Error
Highlight Delete RAID Volume and press ENTER. Dank u. Linux is an amazing OS, but when you start to run mission critical services on there and don't employ or train people to support it properly, it is pages like this Does it let you add the disk to the existing array? Check This Out
What type of RAID issue are you experiencing? You would probably need to remove /dev/sda, then move /dev/sdb to /dev/sda, and then install a new /dev/sdb.From: Ben F Reply Just to add - I've just had a Hope that helps From: Kris Reply This is a great guide but unfortunately, I could not apply it to my failed Raid-1situation. I built this computer 4 years ago.
m 0 l ninjayar 6 January 2016 18:24:26 I guess I spoke too soon. I found out, that during the partitioning I got other blocksizes for the new drive: # blockdev --report RO RA SSZ BSZ StartSec Size Device rw 256 512 4096 0 2000398934016 m 0 l jimmysmitty a b G Storage 5 January 2016 15:24:42 The location of the partition is fine. Yes, go to Rebuilding RAID1.
I'm thinking this has to be at a hardware level, since the Windows CD won't even try to load if all HDs are disconnected. Matthew R Roller Reply Thank you so much! I'm off to that that link you provided. For the future, though...RAID 1 ain't a backup.
out side of the RAID array each drive should be bootable I believe outside of a RAID 1 array, the filesystem wouldn't even be readable let alone bootable. RAID Volumes: ID Name Level Strip Size Status Bootable 0 Volume0 RAID0(Stripe) 128KB 223.6GB Failed No Physical Disks: Port Drive Model Serial # Size Type/Status(Vol ID) 0 SAMSUNG HM120JI S09GJ10L209832 111.8.GB run 'chroot /mnt/sysimage' 5. Can I make a recovery or boot disk on another machine to restore access to my main computer?
This works even with RAID 1. Just did it and your steps worked perfectly. This is for moving to a different controller, but I see no reason that it should not work for moving drives on the same controller. Some things that may seem like an issue may or may not be, even.
Evidently, that let Windows start using the boot partition on my D drive or the BootCD (not sure which) whereas when booting without the BootCD, Windows wouldn't start at all. I really do. Yes, then please proceed to the next step. Bought a exact identical drive 2.
Your instructions made it quick and painless to replace the drive and not lose any data. his comment is here The answer is 'yes', easily found in the man page once I knew the option existed. m 0 l jimmysmitty a b G Storage 6 January 2016 18:34:04 It does seem like Intels RST is having a fit. I rebooted again without the Windows install disk and Bob's your uncle.
- Forum Raid 1 failed now can't boot drive Forum Bymistake I have formatted c drive and now it is showing error on trying to install windows xp.
- Simply because having to get a new disk is not fun and I've also seen arrays degraded and the disks are fine.
It just requires having enough SATA connections.From: the_rusted_one Reply Actually, it is much easier than all that. Here's what you do (PREFERABLY BEFORE the failure event, but still this Which I have already done but didn't solve the problem. asked 1 month ago viewed 57 times Blog Stack Overflow Podcast #92 - The Guerilla Guide to Interviewing Related 1Do I have a raid or not?1SSH Commandline - Ubuntu x64 dedicated http://lebloggeek.com/raid-1/raid-5-degraded.html The computer can be used normally while it is rebuilding the RAID 1 volume.
Chances are the order of the drives shown in the configuration display is the same as the order of the SATA ports the drives are plugged into. Again, because it's not finding it on C:. Knowing which port is faulty lets you know which drive inside the system is having the issue.
Critical RAID Error SSD's show Status Critical in Raid 0 and Raid 1.
Thank you. There I executed fsck -y /dev/sda sda and sdb are busy. Nothing works. Nevertheless the disks are of exact the same size and geometry.
The only thing I would suggest is trying to shrink your main partition on Volume) and make the 100MB boot partition there that way in the future you can wipe/format the Jan 24, 2008 System will not boot past detecting RAID array Aug 8, 2005 Add New Comment You need to be a member to leave a comment. I didn't watch the boot-up, so I restarted. http://lebloggeek.com/raid-1/raid-movie.html Similar has happened to a good friend of mine.
Any ideas how to fix this? Does it matter which of the two Volume0 drives I do this to or need I do it on both? Reinsert the drive back into the first PC, exactly as it was. If it happens a lot, then you would be wise to look in to it (and always wise to have backups).
Disk Array Operation Note: You can add, remove disks, or set them as faulty without stopping an array. 1. NOTE: There is a new version of this tutorial available that uses gdisk instead of sfdiskto supportGPT partitions. 1 Preliminary Note In this example I have two hard drives, /dev/sda This can be done with any array type. Windows made some changes and requested a reboot, and everything is working again through numerous reboots this time.
I cannot locate a bootable recovery disk any longer. I now have: RAID 1, bootable, two 1TB drives [Volume0, C:] One 1TB data drive [D:] One 4TB data drive [Windows Virtual Mirror Array, M:] My next trick was going to