Home > Raspberry Pi > Openelec Can't Access Tty Job Control Turned Off

Openelec Can't Access Tty Job Control Turned Off

Contents

New build also has another debug option. I'll try it. May and June saw improvements to both drivers. Restarted the reboot cycles and the next reboot froze at the initial OpenElec screen (OpenELEC (your) - Version: 5.0.8 [Build #418]).

I'm hoping only one delay is actually required. For now, Transcend and Samsung EVO cards are best avoided. I added in an SD card performance test (write 500MB file, read 500MB file, delete 500MB file) which saw a consistent 10MB/sec write and 16MB/sec read and added an additional 30 So, for now, please test: mmc_debug=0x2000 and then mmc_debug=0xffff0000 AlecEdworthy commented Apr 20, 2015 @ernstblaauw With bcm2835_mmc.mmc_debug=0x1fff did you have issues (corruption, freezing etc) on the 21st reboot or just stop

Openelec Can't Access Tty Job Control Turned Off

However after reboot 19 there was sufficient corruption to stop the Pi booting normally, but fsck was able tot fix it. KODI PRO 88,909 views 5:56 Solucion IPTV Stalker(Kodi): Canales de cable gratis en windows (Agosto 2015) - Duration: 9:16. Another power cycle and I get dropped to the debugging shell and an fsck is needed to fix it (lots of things it had to fix). If we don't then we'll have to go with a fix that cures all the tested sdcards and if other sdcards have issues in the future we may need further tweaking.

Remove the power and the Rpi2 boot without errors. popcornmix commented Apr 19, 2015 @AlecEdworthy that is interesting. The sdhost block was designed for mobile use, so it shouldn't be a big power drain, but it does need a bit more hand-holding from the ARM than the mmc block. Fsck -fy /dev/mmcblk0p2 Sign in to make your opinion count.

You might want to post a log file as well, and see if that gives any indication of what's happening. Openelec Fsck Manually I used the following test command: RUN=0; while $(true); do RUN=$[$RUN+1]; echo Reboot cycle $RUN; sshpass -p "openelec" ssh [email protected] '({ sleep 2; reboot; } >/dev/null &) ; exit ' ; if 0x1f is a failure, then you could sanity check the inverse of that which should pass. On a new cycle of 20 reboots mmc_debug2=0x7 has frozen on reboots 4 and 19 but a cold start has got it going again.

[email protected]:~/Downloads/f3-6.0$ sudo ./f3probe --destructive --time-ops /dev/sdb F3 probe 6.0 Copyright (C) 2010 Digirati Internet LTDA. Error In Mounted Storage Openelec After a few reboots i had again sd card errors. I reproduce the bug by running apt-get install network-manager and sudo reboot. missmah commented Jul 27, 2015 I also have a 16GB Samsung EVO MicroSD card and I'm seeing the same type of issues as those illustrated in the image posted by sidey79

Openelec Fsck Manually

ghollingworth commented Apr 2, 2015 If your failure is 100% reproducible then it would be interesting to see, currently I'm having trouble reproducing the problem (only seen it twice in the popcornmix commented Apr 13, 2015 @NitroG42 I wonder if you could test this kernel: https://dl.dropboxusercontent.com/u/3669512/temp/kernel7.img By default it should be the same as the current "rpi-update" kernel, but supports some debug Openelec Can't Access Tty Job Control Turned Off It’s possible to use your SD only for booting up your device, and keep all the data on a USB stick or hard drive. Fsck Openelec I got the same issue today while updating wolfgram-engine with apt-get.

You need to gather the bits and pieces you need to make it work the way you want it to, and with much head scratching and healthy googling, figure out how Go to Add Video Source. Basically, after a fresh install of Raspbian, I create a file ( sudo touch /forcefsck ) to run fsck on next boot, I reboot and then lots of errors are found I've popped the SD card out to run an fsck using a separate RapPi to check for any unseen issues and none were found. Raspberry Pi Sd Card Corruption Fix

pelwell commented Oct 7, 2015 The sdhost driver was added on the 25th of March, and the mmc_debug flags appeared in April. Samsung 16GB class10, Pi B model 512mb, overclocking doesn't seem to make a difference. Please help me out. But if it does, you might save yourself a couple of bucks.

A popcornmix commented Apr 21, 2015 As long as we get below the 0x0f0f0000 numbers I suspect it won't be significant (that is 15us per sdcard host control register access - Kodi Fsck I wonder how many years I've in effect added to my mini-SD card and RasPi's lives with all this testing, rebooting etc. XK MC 4,556 views 6:39 See how Raspberry Pi 2 handles HD IPTV in Kodi/XBMC 14.2 Helix - Duration: 8:07.

but perhaps I should have removed it each time along with the break= option...

The requirements are pretty modest – you’ll need at least a 2GB card, but you’ll most likely want something with bit more space for storage. Board index The team Delete all board cookies All times are UTC

current community chat Raspberry Pi Raspberry Pi Meta your communities Sign up or log in to customize your SD Card still is getting corrupted. Openelec Could Not Repair File System Note that their indexes of our content may be out of date.

When the time comes to restore or re-image a new card, you can use the same utility to clone the image back onto the new SD card. sidey79 commented Jun 21, 2015 Hi there, i'm running a RPI2 with an ADATA SD Class10 Card. Can you try: bcm2708-dmaengine.dma_debug=0x1f instead of the bcm2835_mmc.mmc_debug option and report the results. If you don't have a login yet, please create a free account.

Loading... I've kicked off the same test using bcm2835_mmc.mmc_debug=0x001f0000 bcm2835_mmc.mmc_debug2=0x0 to soak it instead. Personal Open source Business Explore Sign up Sign in Pricing Blog Support Search GitHub This repository Watch 355 Star 1,895 Fork 739 raspberrypi/firmware Code Issues 92 Pull requests 0 Projects How does a jet's throttle actually work?